Attention
- Check all accessories before installation, NO return after installation, but there is a possibility for repairing or discounted returns.
- Please do not use a high-pressure water gun to flush the host and the cameras, the product is only waterproof against the rain.
- Please do not use alcohol, stain removal solution and other corrosive solvents to wipe the host and lens to avoid damaging the appearance of the product and waterproofness.
- Please make sure to connect all the units before turning on the power.
- Do not fold the cable lines during installation.
Special attention:
- Please use a certified 8-256GB MICRO TF memory card with a CLASS 10 classification or above and format the memory card before first use.
- Long-term use of the memory card will cause fragmentation, so it is recommended formatting the memory card regularly.
- Press the rubber plugs after inserting to ensure the waterproofness of the product.
Please read this manual carefully before use and keep it for future reference.
Explanation of Main Components
Accessories Details
Description of main parts and key functions
Connection Method
- Put the multimeter on DC, the black test connects to the negative battery pole, the red test connects to the test line.
- When the ACC is OFF, there should be no output, the multimeter shows nothing; when the ACC is ON, the multimeter should show 12V voltage, at this time has found the ACC power line.
-
If you haven't found the ACC line, please use the red pen to replace the test line repeatedly (the black pen connected to the negative pole remains unchanged) until you find the ACC line.
Description of the main menu screen
CarPlay & Android auto connection instructions
The Bluetooth function and WiFI function of the mobile phone must be turned on at the same time. Click the "Interconnet" window on the home page to enter, click the CarPlay icon again, and follow the prompts.
Note: For the first connection, turn on the cell phone Bluetooth, connect to the host Bluetooth, then wait for 5-10 seconds, when the cell phone WiFi is in the open state, the Android auto interface will automatically transmit. Click the home button to return to the main interface of the dash cam.
Main Settings screen description
- Language: Multiple languages
- Time setting: Set the host time (after connecting to GPS/Wi-Fi/Bluetooth, the howill update the time automatically)
- Phone audio: ON/OFF, when switch to OFF the mobile phone sound plays by the host.
- Key Volume: ON/OFF the touch key tone.
- Wi-Fi switch: ON/OFF, the Wi-Fi connection distance is 10 meters in a straight without obstruction.
- Pressure: Pairing for tire pressure detection
- Screen saver: Set the auto-lock time of the screen
- GPS info: Check GPS signal information
- Format SD: Format the memory card
- Reset: Reset the host
- Version: Check the version/Bluetooth name/Wi-Fi name and password
Tire Pressure Detection Interface Explanation
- Set the tire pressure unit Bar or Psi according to your needs.
- Set the air pressure alarm value according to different models. If the tire pressure is too low or too high beyond the set value, a flashing reminder will appear. First install the reverse to the bottom of the tire valve and click "start". The FRO tire pressure number at the top flashes, at this point,set the front wheel A (FW) and the blinking will stop when pairing is complete. Continue to pair rear wheel B (RW) while BAC is blinking and the blinking will stop when pairing is complete. After the front and rear tire pressure sensors have been successfully matched, screw the reverse lug nuts back against the tire pressure sensors to prevent the sensors from falling out. When you need to re-inflate the tire, loosen the reverse nut first, then screw the sensor, after inflation, the tire pressure will be displayed successfully without any re-pairing, if the value is not displayed, after a certain distance riding, the value will be displayed. If the value is still not displayed, please follow the steps to re-pair the sensor. When the tire pressure display is inaccurate, please check whether the sensor is installed correctly and whether the air pressure unit of the inflation tool is consistent with the host.
Click Driving recorder
- Homepage: Press to return to the previous page
- Settings: Press to entry the menu
- Playback: Press to return to the playback interface
- Recording: Press to turn on/off voice recording
- Lock: Press to lock/unlock the pictures of front and rear cameras
- Take a photo: Press to take a picture from the front and rear camera at the same time
- Video recording: start/pause
- Time: Time/date
- Altitude
- Position
- Recording time
- Speed
Recorder setup menu description
Click the recorder interface setting button to enter the menu interface. Click to return to the recorder interface.
- Resolution: Set video resolution
- Loop: Set 1/3/5 minute loop recording
- G-sensor: Collision sensitivity settings
- Date: Time watermark
- GPS switch: GPS signal
- Recording: Video sound settings
- GPS speed: GPS speed record
- Compass: Compass bearing
- GPS: GPS switch
- Back: Rear lens mirror function
Description of the playback interface
Instructions for WiFi connection
When the WiFi is enabled, find the name MT91CXXX in your phone's WiFi settings and enter the password 12345678 to connect. After successful connection, the WiFi logo will change from white to green.
- Turn on the WiFi in your phone's WLAN settings, select the MT91C network name, and enter the password 12345678 to connect.
- Some android mobile phones will prompt "no internet access in this network" or similar information, please select the option of "connect only this time" or "always connect". (Note: Dash cam WiFi is only used for the connection and operation of the host and the mobile phone APP, no internet connection).
Instructions for WiFi connection
iOS system connection procedure
- Settings - Wi-Fi - Select the MT91C network - enter password 12345678 to connect.
- Open KYCAM2-APP, press "Enter recorder", the dash cam prompts to use GPS location, select "Allow when using APP" and "Allow to connect to local network".
- Press "Into Camera" to enter the home page to view and set up.
- Album: Press to view downloaded videos and photos.
- More: Settings - language - Time - Offline maps
Description of APP Keys
Main Features
Protection level | IP65 |
Screen projection | Apple CarPlay Android auto: Support Apple CarPlay Android auto |
Built-in battery | Coin cell batteries |
Quantities of camera | 2 (front and rear) |
Display | 6.25-inch IPS display |
Parking monitor | √ |
WiFi/APP interface | √ |
GPS track | √ |
Format | H.264: Video format TS, Compression format H.264 |
Memory card capacity | 8-256GB C10 Memory Card |
Voltage Requirement | 12-30V to 5V 2A |
Common Troubleshooting Solutions
1. How to disconnect CarPlay or Android auto?
Answer: Just turn off the WiFi or forget the Bluetooth device.
2. How do I reconnect to the CarPlay/Android auto after manually disconnecting it?
Answer: Just reconnect to the dash cam through Bluetooth.
3. How do I reconnect to CarPlay/Android auto after restart the dash cam
Answer: It will be connected back automatically when Bluetooth and WiFi are both enabled.
4. How to make use of the App-Kycam2 when connected to CarPlay?
Answer: Both can be operated simultaneously.